How do you set rebounds on Fox shocks?
0:251:41Fox Suspension 3: Adjusting Your Rebound - YouTubeYouTubeStart of suggested clipEnd of suggested clipStarting with pull slow bikes returning way to slow its going to back down as well going all theMoreStarting with pull slow bikes returning way to slow its going to back down as well going all the way to the negative opening everything up.
How do I set up my suspension?
2:439:2210 Minute Suspension Setup | Get Your MTB Dialled FAST! - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition. So as to settle the fork naturally into its travel. Making sure not to bounce on the forkMorePosition. So as to settle the fork naturally into its travel. Making sure not to bounce on the fork and compress it any further gently. Move your weight back off of the fork. And come to a gentle.
How do you set up a Fox Float fork?
Setting Fork Air PressureUnscrew the blue air cap on top of the left fork leg counter-clockwise to expose the Schrader valve.Attach a FOX High Pressure Pump to the Schrader valve.Pump your fork to the appropriate pressure as listed in the Suggested starting points for setting sag table below, then remove the pump.More items
How do I adjust my rear Fox suspension?
Turn your rebound knob to the closed position (full clockwise) until it stops. Then back it out (counter-clockwise) to the number of clicks shown in the table below. Rebound controls the rate of speed at which the shock extends after compressing. Set the open mode adjust to setting 1.
How much air do I put in my Fox shocks?
Add air pressure to the main air chamber in ~50 psi (3.4 bar) increments, slowly cycling the shock after every 50 psi (3.4 bar) addition.
What PSI should my FOX shock be?
Do not exceed 300 psi (20.7 bar), the maximum FLOAT air pressure! Remove the pump. Sit still on the bike in your normal riding position, using a wall or a tree for support. Pull the sag indicator o-ring up against the rubber air sleeve seal.
What PSI should my suspension be?
Start with where you should be in the manual, assess how much travel youve used after a typical ride. If you are not cycling through your suspension, let out 5 psi at a time per ride.
What does bump mean in suspension?
Bump Steer Definition. Bump Steer is when your wheels steer themselves without input from the steering wheel. The undesirable steering is caused by bumps in the track interacting with improper length or angle of your suspension and steering linkages.
How much PSI is a Fox Float?
Hightower LTFox Float DPXRider WeightAir PressureShock Sag100lbs (45.5kg)145 psi16-19 mm120lbs (54.4kg)165 psi16-19 mm140lbs (63.5kg)180 psi16-19 mm8 more rows
How do I read a Fox shock description?
0:463:44What do FOX Tune IDs mean - YouTubeYouTube
How much air should I put in my Fox 36?
Do not exceed maximum air pressure: 36 FLOAT and Rhythm maximum air pressure is 120 psi. The rebound adjustment is dependent on the air pressure setting. For example, higher air pressures require slower rebound settings.
What PSI is Fox 36?
Setting Sag36 float AIR SPRING SETTING guidelinesRider WeightAir Pressure145 - 155 lbs.53 psi155 - 170 lbs.55 psi170 - 185 lbs.62 psi7 more rows
How much air should I put in my shock?
The proper pressure of an air shock should be between 35 and 75 PSI. If it is any lower than this, the shocks will need to be filled with air.
How much air should be in my shocks?
The proper pressure of an air shock should be between 35 and 75 PSI. If it is any lower than this, the shocks will need to be filled with air.
Which type of suspension is best?
Multi-link and dual wishbone systems are the holy grail of suspension designs, allowing engineers to achieve agile handling without compromising ride quality.
Is suspension expensive to fix?
You need to look at the cost to repair or replace the suspension, plus the labor cost that will be associated with taking your car to an auto mechanic. The average cost of a suspension repair is between $1,000-$5,000.
How much air should I put in my fox DPX2?
Do not exceed maximum air pressure: FLOAT DPS and DPX2 air shocks have a maximum air pressure of 350 psi. 4. Remove the pump. 5.
How do I read a Fox tune code?
0:403:44What do FOX Tune IDs mean - YouTubeYouTube
How do I know which Fox shock I have?
On FOX shocks 2013+ you can normally find a shock custom tune id printed on the label around the air sleeve:In the above picture we can see the ID being C372. The page will list information regarding the specific code, the above shock gives us:More items •26 Apr 2017
How do I air up my Fox 36?
Learn how to use the FOX High Pressure PumpRemove the blue air cap from the top of the left fork leg. Let the air out of the fork. Loosen the bottom nut 3-4 turns with a 10mm wrench. Compress the fork as much as possible. Pull the air-shaft assembly from the fork.